Location: Home > Product  

E3JM Series Power Supply Built-in Type Photoelectric Sensor

E3JM Series
Power Supply Built-in Type Photoelectric Sensor

E3JM series power supply built-in type photoelectric sensor is a square shape photoelectric sensor with 30ms turn-on delay. The detection methods of the E3JM series are thru-beam, retro-reflection, and diffuse-reflection. According to the wiring method, E3JM series photoelectric sensors can be divided into wiring type and terminal type. E3JM series photoelectric sensor have a built-in relay to drive high-current loads and can be equipped with an optional delay output function. E3JM series photoelectric sensors use high-quality chips, which have the advantages of long life and high reliability, and can adapt to complex working environments. The operating status of the sensor can be directly observed through the red LED, E3JM series photoelectric sensors are IP65 protected (IEC standard). E3JM series photoelectric sensors also have a enhanced shell strength and improved wire breakage countermeasures. For more information about the proximity sensors, please visit "What is Photoelectric Sensors".

  • E3JM



How to order


● Complete functions, built-in relay, can drive high current load

● Optional delay output function

● Long life and high reliability, high environmental adaptability

● The red LED shows the operating status of the sensor

● Enhanced shell strength, and improved wire breakage countermeasures

● IP65 protection structure (IEC specification)

● Please read "Precautions for Photoelectric Sensors" before use


● Turn-on Delay: 1.5ms

● Light Source: Infrared light 660nm

● Detection Method: Thru-beam, Retro-reflection, Diffuse-reflection

● Wiring Method: Wiring type, Terminal type

● Supply Voltage: DC type — 12-24VDC (6-36VDC) with voltage pulsation (p-p) below 10%; AC type — 110-220VAC (90-250VAC), 50/60Hz; DC/AC type — 12-240VDC / 24-240VAC, 50/60Hz

● Power Consumption: Below 3VA

● Control Output: Below 2A (contact life above 100,000 cycles)

● Allowed Shock and Vibration: B≤30g, T≤11ms, f≤55Hz, a≤1mm

● Ambient Temperature (operating, storage): -30-+65°C (non-freezing, non-condensing)

● Ambient Humidity (operating, storage): 35-95%RH

● Insulation Impedance: Above 50 MΩ (between the charging section and the housing, using a DC500 megohmmeter)

● Withstanding Voltage (1min): 1000VAC, 50/60Hz (between charging section and case)

● Temperature Effect: If the temperature range is -30 to +65℃, the sensing distance is within ±15% of the detection distance at +23℃; if the temperature range is -25 to +60℃, the sensing distance is within ±10% of the detection distance at +23℃.

● Voltage Effect: If the voltage range is within ±15% of the rated supply voltage, the sensing distance is within ±10% of the detection distance at the rated supply voltage.

● Protective Structure: IP65 (IEC standard)

● Material: Housing — Die-cast aluminum / ABS; Detection surface (Lens) — PMMA


E3JM Series Photoelectric Sensors
Sensing MethodsDiffuse-reflectionRetro-reflectionThru-beam
Light-On Setting (DC)E3JM-DS70M4E3JM-R4M4E3JM-10DM4-10L
Light-On Setting (AC)E3JM-DS70M4E3JM-R4M4E3JM-10DM4-10L
Dark-On Setting (DC)E3JM-DS70M2E3JM-R4M2E3JM-10DM2-10L
Dark-On Setting (AC)E3JM-DS70M2E3JM-R4M2E3JM-10DM2-10L
Detection Distance70cm±10%4m±10%10m±10%
Standard Sensing ObjectOpaqueOpaqueOpaque
Detection Distance adjustmentFixedSensitivity regulatorFixed
Response Time30ms30ms30ms
Outline Dimension DrawingFigure1

Dimensions & wiring diagram

E3JM series, dimensions and wiring diagram, Photoelectric Sensor



Upload page data and generate pages.

  Get in touch with us now!

Please take a minute or two to complete this simple form to get reply in 24 hours, thank you!

*Please check the trash box of your mailbox, if you do not receive our email.